Techstream help * good tech please help **fixed*

Techstream help * good tech please help **fixed*

Postby Morksvigo05 on Mon, 25 Jun 2018 9:57 +0000

Hi guys I have a thread up about my abs
I rectified the open circuit to both RR a RL speed sensor
I hooked it up to techstream cleared code and it stays off then I drive about 20 Meters abs light comes back on
Hook it back up to techstream keeps on coming up rh speed censor circuit with a little frozen sign next to it ,
continuity is good at the ba2 connecter to the back sensor I cleaned and rings as they were dirty
The freeze sign worries me is it stored can I erase it
Always does the same thing goes off and stays off and 20 Meters down the road comes back on
Any help will be greatly appreciated
I know I'm close but not close enough
I know my drum pads are low on the r hand side but surely it's not that there's no sensors or nothing for that and the light comes back on before I even brake

*** Changed rear pads no good
Last edited by Morksvigo05 on Tue, 26 Jun 2018 11:23 +0000, edited 1 time in total.
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw


 

Re: Techstream help * good tech please help *

Postby flip9 on Mon, 25 Jun 2018 12:02 +0000

It should give you a diagnostic trouble code (DTC) like C0200/31.
User avatar
flip9
 
Posts: 269
Joined: Tue, 05 May 2015 12:33 +0000
Location: Sydney

Re: Techstream help * good tech please help *

Postby Morksvigo05 on Mon, 25 Jun 2018 12:04 +0000

Is it possible I'm getting good continuity whilst stationary even when I spin wheel by hand it's like when I get to about 20 30 K while under way it comes back on
Like start checks fine etc
Should mention it's a new sensor old wire
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Techstream help * good tech please help *

Postby Morksvigo05 on Mon, 25 Jun 2018 12:25 +0000

Code co210
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Techstream help * good tech please help *

Postby Morksvigo05 on Mon, 25 Jun 2018 12:28 +0000

Morksvigo05 wrote:Code co210


I'm thinking change wire to ba2 to speed sensor
And only choice after that really is abs module ????
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Techstream help * good tech please help *

Postby flip9 on Mon, 25 Jun 2018 1:28 +0000

That code is for the rear right wheel speed sensor.

Go to the sensor and inspect it. Make sure its bolted down and seated properly.

Undo the sensor plug and grab a multimeter. Check resistance between the two pins of the sensor and you should get 0.6 to 1.8 kΩ

then test between Pin 1 to ground (chassis) then Pin 2 to ground. You should get 10 kΩ or more for both.

If the sensor is fine then it might be the hub itself. I would still try another sensor first though.
User avatar
flip9
 
Posts: 269
Joined: Tue, 05 May 2015 12:33 +0000
Location: Sydney

Re: Techstream help * good tech please help *

Postby Morksvigo05 on Mon, 25 Jun 2018 3:00 +0000

Fixed it guys I ground down the face of which the sensor seats on the actual diff itself had all rust and stuff
Filed down the actual plastic of the sensor that seats on the face I ground and whalla done abs light cleared and stayed cleared so happy
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw


Return to Electrical

Who is online

Users browsing this forum: No registered users and 14 guests