Engine loses power - P2008 Error Code

Turbo, Manifolds, Exhaust, Intercooler, Internals etc

Re: Engine loses power - P2008 Error Code

Postby AshA on Mon, 28 Jul 2014 5:25 +0000

boxhead55 wrote:No 1000 km and a bad decision caused this. Image
Words can not describe how dirty this filter was



Thats one scary looking filter.
AshA
 
Posts: 121
Joined: Sat, 19 Nov 2011 11:18 +0000


 

Re: Engine loses power - P2008 Error Code

Postby boxhead55 on Tue, 29 Jul 2014 4:58 +0000

Sure was and check the fluid that came out of rhe bottom. Anyone who thinks the Gen filters are cap refer to this pick
User avatar
boxhead55
 
Posts: 2864
Joined: Sat, 15 Jun 2013 3:46 +0000

Re: Engine loses power - P2008 Error Code

Postby boxhead55 on Tue, 29 Jul 2014 5:03 +0000

Image

Filthy sides and bottom. Clean top.
User avatar
boxhead55
 
Posts: 2864
Joined: Sat, 15 Jun 2013 3:46 +0000

Re: Engine loses power - P2008 Error Code

Postby dan9245 on Fri, 01 Aug 2014 10:47 +0000

Hey guys

I have a 2008 Toyota hilux SR 4x4 3.0 TD... started it up this morning and came up with a fault code on my scangauge 'P0048' Turbocharger/Supercharger Boost Control 'A' Circuit High"

turbo sounded like it was whining on start up and also wouldnt rev over 2000rpm.. I tried clearing the code and it just came back up straight away several times.. Even tried disconnecting battery... still no luck.!!

Has any one else had this code and what did you do or can you do to fix it...

Cheers fellas
User avatar
dan9245
 
Posts: 170
Joined: Thu, 24 Oct 2013 6:14 +0000
Location: Nowra, NSW

Re: Engine loses power - P2008 Error Code

Postby D22marshall on Tue, 05 Aug 2014 3:48 +0000

A week of nothing now p0102 p0113 p1251 and last but not least p2008
D22marshall
 
Posts: 48
Joined: Wed, 20 Nov 2013 9:14 +0000

Re: Engine loses power - P2008 Error Code

Postby boxhead55 on Tue, 05 Aug 2014 5:01 +0000

Rat attack on the wires under the intercooler.
User avatar
boxhead55
 
Posts: 2864
Joined: Sat, 15 Jun 2013 3:46 +0000

Re: Engine loses power - P2008 Error Code

Postby D22marshall on Tue, 05 Aug 2014 7:03 +0000

Intercooler came off for manifold clean so unlikely. Can the maf cause all these new codes?
D22marshall
 
Posts: 48
Joined: Wed, 20 Nov 2013 9:14 +0000

Re: Engine loses power - P2008 Error Code

Postby boxhead55 on Tue, 05 Aug 2014 7:44 +0000

No
User avatar
boxhead55
 
Posts: 2864
Joined: Sat, 15 Jun 2013 3:46 +0000

Re: Engine loses power - P2008 Error Code

Postby boxhead55 on Tue, 05 Aug 2014 7:44 +0000

Term high. Means open circuit.
User avatar
boxhead55
 
Posts: 2864
Joined: Sat, 15 Jun 2013 3:46 +0000

Re: Engine loses power - P2008 Error Code

Postby boxhead55 on Tue, 05 Aug 2014 7:45 +0000

Could be a chafed or externally or internally broken wire
User avatar
boxhead55
 
Posts: 2864
Joined: Sat, 15 Jun 2013 3:46 +0000

Re: Engine loses power - P2008 Error Code

Postby D22marshall on Tue, 05 Aug 2014 11:24 +0000

Who should I see to best sort it??
D22marshall
 
Posts: 48
Joined: Wed, 20 Nov 2013 9:14 +0000

Re: Engine loses power - P2008 Error Code

Postby D22marshall on Wed, 13 Aug 2014 5:42 +0000

Right again boxhead maf didn't fix it what now?
D22marshall
 
Posts: 48
Joined: Wed, 20 Nov 2013 9:14 +0000

Re: Engine loses power - P2008 Error Code

Postby D22marshall on Wed, 13 Aug 2014 6:38 +0000

Box just got it checked again only fault now 1251 step motor! Anyone had this?
D22marshall
 
Posts: 48
Joined: Wed, 20 Nov 2013 9:14 +0000

Re: Engine loses power - P2008 Error Code

Postby boxhead55 on Wed, 13 Aug 2014 8:03 +0000

There have been cases when the wire has broken in the wiring loom that goes to the stepper motor. Normally around the front left of the sump when the wire loom sometimes touches the sump. And sometimes the wire will brake in the insulation just near the plug to the stepper motor wire will look good but it is broken inside
User avatar
boxhead55
 
Posts: 2864
Joined: Sat, 15 Jun 2013 3:46 +0000

Re: Engine loses power - P2008 Error Code

Postby D22marshall on Wed, 13 Aug 2014 10:17 +0000

Ok cheers will take a look
D22marshall
 
Posts: 48
Joined: Wed, 20 Nov 2013 9:14 +0000

Re: Engine loses power - P2008 Error Code

Postby D22marshall on Wed, 13 Aug 2014 10:26 +0000

Wiring all looks to be clear and no evidence of rubbing anywhere can I do anything to check the stepper at the turbo?
D22marshall
 
Posts: 48
Joined: Wed, 20 Nov 2013 9:14 +0000

Re: Engine loses power - P2008 Error Code

Postby boxhead55 on Wed, 13 Aug 2014 1:03 +0000

There is an active test you can do using techstream
User avatar
boxhead55
 
Posts: 2864
Joined: Sat, 15 Jun 2013 3:46 +0000

Re: Engine loses power - P2008 Error Code

Postby D22marshall on Wed, 13 Aug 2014 1:51 +0000

So does that mean my only option is back to toyota? Can I buy the stepper what sort of $$? Thanks again box man
D22marshall
 
Posts: 48
Joined: Wed, 20 Nov 2013 9:14 +0000

Re: Engine loses power - P2008 Error Code

Postby boxhead55 on Wed, 13 Aug 2014 3:46 +0000

Mate best to see if that's the fault first. You can not buy it by itself. It comes as a turbo assembly.
User avatar
boxhead55
 
Posts: 2864
Joined: Sat, 15 Jun 2013 3:46 +0000

Re: Engine loses power - P2008 Error Code

Postby D22marshall on Wed, 13 Aug 2014 3:59 +0000

Ok the fault came up 1251 intermittent on my mechanics scanner. Do I now ask toyota to run a test on the stepper turbo set up? Any advise would be great I feel like I have made progress but still so far away from success.
D22marshall
 
Posts: 48
Joined: Wed, 20 Nov 2013 9:14 +0000

PreviousNext

Return to Engines

Who is online

Users browsing this forum: No registered users and 3 guests