Critter350

Want to show off what you've done to your rig? or have a custom project to show? Post it up here!

Re: Critter350

Postby Critter350 on Mon, 27 Apr 2020 6:41 +0000

Cheers Myralga

I looked at lots of tanks and planned this out (ie procrastinated) for a long time, to get to the point where I’m making it up as I go.
This tank is probably still the best shape to fit in the space available (other than custom), and $60 is hard the beat.




Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA


 

Re: Critter350

Postby Critter350 on Mon, 27 Apr 2020 6:50 +0000

Isolation is good for having some extra time, but the heavy lifting gets a bit complicated. Managed to get the canopy off and tray flipped solo. Image

Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Mon, 27 Apr 2020 7:03 +0000

Cut the tray for battery access and mocked up the drawer.
Image

General layout. Battery box and water tank are fixed. Drawer floor is Ali security mesh, shovel, treds and tent poles(1 in the picture, holds 6) with the drawer.
Image

If this photo is confusing, the upturned tray is being used as a bench, flip the tray round other way up and sit on top of the rest here.1m drawer runners will extend the drawer to the back of the mesh.
Bit of spare room for light stuff, maybe hoses.


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby NZMarkb on Tue, 28 Apr 2020 2:19 +0000

Looking good mate
I know what you mean about the heavy lifts, just fitted a winch & Bullbar on my 200 :lol: :lol:
A few skinned knuckles and a sore back
If your not prepared to stand behind our Troops
Then try standing in front of them
User avatar
NZMarkb
Platinum Subscriber
 
Posts: 702
Joined: Thu, 18 Jul 2013 3:48 +0000
Location: Auckland NZ

Re: Critter350

Postby Critter350 on Mon, 06 Jul 2020 11:56 +0000

Calling practical completion of this lock down project. Few tidy up jobs to go but there’s always something to do.
The original scope was to add a water tank. The drawer and battery box were scope creep, and messed with the original water tank location.
So to recap I replaced the original 100mm Z purlin sitting on 40mm unistrut ‘lattice structure’ with 150mm Z purlin rails, for an overall 10mm increase in height.
Image

Battery box is framed in with more Z purlin.
Battery box itself is 1.6mm Ali, cut out with a jigsaw and bent up with an old bed frame and g clamps. Image
Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Mon, 06 Jul 2020 12:03 +0000

Battery box is finished with 12mm marine ply base, reinforced for the 8mm ss threaded rod hold downs
Image
reinforced pump mounts
Image

access for wiring and plumbing
Image then wrapped for insulation.
Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Critter350

Postby Critter350 on Mon, 06 Jul 2020 12:13 +0000

Cut a hole in the tray for access just behind the head board, and made a drop in cover out of the material that was removed.
Image

Water tank bracket is out of steel flatbar, fixed with rivnuts at the front and longer bolts at the spare lifter at the back.
Image
Image
Image
It’s a little left of centre but not so bad. There’s a bit of Lino off cut as padding between the tank and frame, and ss threaded rod to clamp it together.


Sent from my iPhone using Tapatalk
Last edited by Critter350 on Mon, 06 Jul 2020 12:24 +0000, edited 1 time in total.
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Mon, 06 Jul 2020 12:21 +0000

Repipe the fuel filler- as you’d expect Toyota uses a proprietary size filler hose that no one else carries, but the genuine was $65 which is not quite as bad as it could have been. Fills better than it ever has now.
Image


Before and after the ranex + chassis black.
Image

Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Mon, 06 Jul 2020 12:39 +0000

Water tank plumbing uses John Guest push fittings with retaining clips and collets.

Twin taps- the lower is gravity fed, the other is pressure. Our camp wash up bowl and cray cooker pot sit on the step for filling without having to hold.
Image
There’s also a valve at the tank, when that is closed the pump will draw through the lower tap from a head height of 8’ (according to pump manufacturer), for filling from fresh water stream, low level tank, or pre-warmed water in the big pot for a warm shower.
The orange click on fittings are blocked with hot glue, just to keep crud out of the taps.

Filler has a click on fitting too, with the female part mounted to pack rack to retain it, shown disconnected here.
Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Mon, 06 Jul 2020 12:50 +0000

The drawer is 3mm Ali frame. Fortunately I found a good guy that let me use his guilotine and bender. I had 1m drawer slides already so wanted to make use of them. Base is a recycled security door. Handle is a ‘whale tail’ 3 point compression type.
Image

The pole holder on passenger side was one of several ‘whoops’, did not allow for the larger top lip on the front of the drawer, so cut the back off and extended.
Image
The plastic tube holds shovel and rake handles.

Catch plate for the whale tail, good thing I’m not charging by the hour eh.
Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Mon, 06 Jul 2020 1:01 +0000

Few tidy up jobs getting it back together. Bit of mould inside the canopy that cleaned up easy enough
Image

Rubber seal around the rear canopy glass was push in, so removed the glass and reseated.
Image

High mount stoplight red diffuser had melted, so replaced the G4 halogen with LED’s and cut a new red lense out of acrylic (from jaycar). The acrylic was very clear so crass hatch sanded it to obscure, it was also a bit thick so routered the edges with dremel.
Image

Rough enough I think
Image
The bags (picked up for $2 each from landfill recycler) are rubbish on the left, rope on the right. Low value stuff.

Hmm what else...
The number plate lights are ‘glued in’ with high bond silicone.
Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby 1tuff4b on Mon, 06 Jul 2020 6:41 +0000

Nice one bud. Very purposeful ass end :)


Sent from my iPhone using Tapatalk
"Life Begins in Low Range"
1tuff4b
 
Posts: 98
Joined: Wed, 16 Oct 2013 7:08 +0000

Re: Critter350

Postby Critter350 on Mon, 31 Aug 2020 12:16 +0000

Electrical upgrade over the weekend.

Glued a solar panel on the roof and installed a Victron 100/20 controller.

Started with a wash and when it was dry, scrubbed with isopropyl, firstly with a blue chux wipe until I noticed it bleeding blue ink, so swapped for a white rag (wonder if the wife will miss that curtain...)
Image

Product called ‘tool box’, never heard of it before but came recommended. Hated working with it though, so thick it’s so hard to squeeze out the gun, has 10 minute skin time so had to go hell for leather to lay it down and get the panel on. Image

Hoping it holds- the wind can get under it but the suppliers all recommend an air gap anyway.

Panel specs for record purposes, this side is down so can’t read it anymore.

Image

Panel came with those solar connectors, so I made up leads to plug in and connect to the controller. Leads test fine but just didn’t work. Triple checked male - female inside the plugs... end up cutting them off and going Anderson. Silastic in the back of the play to keep water out, but I guess it will also keep water in. See how it goes eh.

Loving the Victron app, geeking out on it a bit.
So far have seen 68W, but it is winter and there’s no tilt on the panel.


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Thu, 01 Oct 2020 7:18 +0000

Just to update on the new solar, back from a 3.5 week 7000km trip to Karajini, Cape Leveque and back around the coast.
No signs of the panel moving.
Best output I’ve seen is 168W, but usually around 140W.
Image
Worked so well I opened the breaker linking crank and house batteries to test, haven’t reconnected. House battery has been on solar only for the entire trip and reaches float voltage by about 1pm (maybe earlier, never checked). Figure less load on the alternator may last longer.
Battery voltage overnight drops to around 12.2V which is about as low as I’d want to go for battery longevity, but is fine for now. When this 100ah flooded wet cell dies, I’ll probably replace with a lithium, for weight as well as capacity.


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Sun, 23 May 2021 12:35 +0000

Went with DIY lithium, 4x271Ah CATL cells, 250A Daly BMS and home made aluminium case.
The LiFePO4 cells expand and contract as they charge / discharge, and keeping some pressure on helps them last longer. So the case was designed to apply some pressure, then lined with off cut Lino. Image
Image
Image

Took 5 days to charge the battery from solar, in winter.


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Sun, 23 May 2021 12:38 +0000

New front brakes at 263700. DBA T3 rotors with DBA extreme performance pads.
Cleaned the mud out of the rears and painted the hub centres for good measure. Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby AmeriKUN26 on Fri, 11 Jun 2021 5:14 +0000

Just caught up on your build, looks great!
User avatar
AmeriKUN26
 
Posts: 167
Joined: Fri, 28 Feb 2020 12:19 +0000
Location: Florida USA

Re: Critter350

Postby Critter350 on Tue, 20 Jul 2021 7:51 +0000

Thanks AmeriKUN, following yours too with great interest.


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Tue, 20 Jul 2021 8:05 +0000

Bit more on the electrical recently.
Alternator died recently. Tested direct charging from the alternator to the lithium, worked fine and pushed about 30A. Tested for about 2-3 min while walked around with clamp and volt meter, then opened the breaker again. About 100km later the alternator light came on. Pretty sure it’s original so 14 years is not a bad run, considering it’s seen some water too.
Replaced with 160A unit, enough juice to run stereo, spotties and still charge both batteries.
But started to worry a bit it can probably put out too much current and the lithium BMS might shut down.
So installed a 12/12 30 Victron. Seems overkill because I “never” need to charge from alternator, but never say never and if I do need it, I’ll want it to work without tripping the BMS.
Added bonus was removing the VSR and breaker under the bonnet, now connected via 60A fuse. Have left the breaker in the rear, closing it will // the two batteries. Figured this will be handy for running the car stereo for extended times, the lithium will keep it charged. Just have to remember to open the breaker before starting the car.

Other small tweak is a switch for the water pump on top of the breakout box. Don’t need to have car turned to accessories any more. Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

Re: Critter350

Postby Critter350 on Tue, 14 Sep 2021 5:47 +0000

Made an ali roof rack using 40mm tube and diamond mesh. Bit of noise but overall happy with it for firewood duties.
Image

Mounting up some lights:
Image
Image

The stedi type X pro are great distance but not so good with spread. Hoping these 3301’s angled out fill the gap.
We’ll set back so shouldn’t glare off the bonnet. Image
Now I look like a rolling add for stedi.
Image


Sent from my iPhone using Tapatalk
Critter350
 
Posts: 524
Joined: Sun, 19 Mar 2017 9:36 +0000
Location: Rockingham WA

PreviousNext

Return to Member Build Ups

Who is online

Users browsing this forum: No registered users and 38 guests