Novice correction - work from the edge of each ripple fold and push out Preventable with correct stretching technique and an extra pair of hands
Re: DB's Build - Vinyl Wrap
Posted: Sun, 23 Oct 2016 9:08 +0000
by DeadlyBeast
Tip for removing side indicator - use a pry bar or other such tool to reach around pillar and release retaining clip
If I was too do again I would remove the snorkel - too much time taken measuring and fitting and rubbish finish leaving it on. Got away with doing the panel in 2 pieces. Snorkel nearly meets the top of flare. Just had to cut a 3mm strip in Measuring and fitting top panel sheet to slide back - waste of time in hindsight
Re: DB's Build - Vinyl Wrap
Posted: Sun, 23 Oct 2016 11:05 +0000
by Donsman
Wrap is looking great
Re: DB's Build - Vinyl Wrap
Posted: Sun, 23 Oct 2016 2:30 +0000
by flip9
Top effort mate. How durable are these wraps?
Re: DB's Build - Vinyl Wrap
Posted: Mon, 24 Oct 2016 7:02 +0000
by DeadlyBeast
Thanks guys. Time will tell how durable it is. It takes some decent bush pins stripes but not direct stone or large branch strikes. Plan is to remove it in 3 years and see if I can be bothered to replace it with a tougher wrap. Avery Dennison do a wrap that lasts 10 years - the technology of vinyl seems to be advancing well
Re: DB's Build - Vinyl Wrap
Posted: Mon, 24 Oct 2016 9:59 +0000
by snakesoup
what makes it stick on?
Re: DB's Build - Vinyl Wrap
Posted: Mon, 24 Oct 2016 11:11 +0000
by DeadlyBeast
pressure activated adhesive
Re: DB's Build - Vinyl Wrap
Posted: Mon, 24 Oct 2016 7:01 +0000
by DeadlyBeast
Air bubble trapped in the recess due to no vent. YouTube suggests using a straw
A drill bit will do
Re: DB's Build - Vinyl Wrap
Posted: Wed, 26 Oct 2016 6:46 +0000
by DeadlyBeast
Cable ties work better - easier to pull out
Re: DB's Build - Vinyl Wrap
Posted: Wed, 26 Oct 2016 7:06 +0000
by DeadlyBeast
An experienced vinyl applicator would cringe at the wrinkles here. I tried to minimise the amount of exposed sheet by working with a bit at a time. I have since learnt the method of "triangles" where the whole sheet is peeled - centre portion only is adhered then divide the sheet in four by pulling and stretching each corner tight to remove wrinkles before adhering the rest down.
Trimmed the edge to 1-2mm overlap of rubber seals using the chisler as a spacer Then just tucked the overlap behind the seal
Re: DB's Build - Vinyl Wrap
Posted: Wed, 26 Oct 2016 1:19 +0000
by TOYZX
And people tell me that I have loads of patients! You da man DB! Was considering doin mine because of all the bush pinstripes but I'm thinking I mite go for plastic dip instead. Good job man!
Sent from my SM-N920I using Tapatalk
Re: DB's Build - Vinyl Wrap
Posted: Wed, 26 Oct 2016 2:54 +0000
by DeadlyBeast
I think I would happily trade in my clumsy wrapping skills for your welding skills any time Cheers mate
Re: DB's Build - Vinyl Wrap
Posted: Fri, 28 Oct 2016 6:18 +0000
by gold member
Hey DB I'm guessing you have done your bonnet? How wide are the sheets of vinyl? The roll I have seen are only 1500 wide, is that wide enough to cover the bonnet? ( if I was not 1500kms away from Home I would simply measure my bonnet) am contemplating this on my rig
Sent from my iPhone using Tapatalk
Re: DB's Build - Vinyl Wrap
Posted: Sat, 29 Oct 2016 8:21 +0000
by DeadlyBeast
Yeah mate - 1500mm does it in one drop
The bonnet is very close to 1500mm at its widest near the hinges. By the time you stretch it a little there is plenty of overlap
Another example of incorrect technique which took way too much time to correct
Correct technique here: https://youtu.be/aU8f8pi06Hs?t=190 (Wish I had of seen this technique before I had finished ) The vinyl used in that vid is Avery Supreme - very different to the one I used but how easy did that look
Re: DB's Build - Vinyl Wrap
Posted: Sat, 29 Oct 2016 4:19 +0000
by Pizza
God damn he made that look easy ,enjoying seeing your progress
Re: DB's Build - Vinyl Wrap
Posted: Sat, 29 Oct 2016 6:20 +0000
by creaky
I could muff up a vinyl wrap in minutes I reckon ! Big props to you taking iron yourself.
Re: DB's Build - Vinyl Wrap
Posted: Sat, 29 Oct 2016 6:39 +0000
by taresk
I was at the limits of my patience vinyl wrapping my 'B' pillars, awesome effort so far, I can't imagine how people do this for a living.
Re: DB's Build - Vinyl Wrap
Posted: Sat, 29 Oct 2016 7:17 +0000
by DeadlyBeast
Cheers guys. Spent many hours wondering how anyone makes money doing this Prepared earlier... ridiculous amount of time just doing the scoop
Re: DB's Build - Vinyl Wrap
Posted: Mon, 31 Oct 2016 7:18 +0000
by DeadlyBeast
Re: DB's Build - Vinyl Wrap
Posted: Mon, 31 Oct 2016 7:27 +0000
by DeadlyBeast
Most difficult panel to wrap - funny how simple it looks in pics Much easier if tub was removed