Priming water filter separator? ** Fixed**

Petrol, gas, fuel tanks etc

Priming water filter separator? ** Fixed**

Postby Morksvigo05 on Wed, 25 Jul 2018 4:54 +0000

Hi guy changed my fuel filters today
My question is I tried priming using the primer for ages not much happening I feel pressure but I have an inline ryco water separator /filter before the factory filter
Would I have to fill it with diesel manually or ?
Any help greatly appreciated
It did start no problems but then it ran out of fuel and stopped because the pre filters dry
Last edited by Morksvigo05 on Fri, 27 Jul 2018 3:27 +0000, edited 3 times in total.
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw


 

Re: Priming water filter separator?

Postby dave g on Wed, 25 Jul 2018 6:43 +0000

Hi mate undo the out hose from your fuel filter place a hose on it into a jar and pump the hell out of you pump sounds if you have a air lock keep pumping to you get fuel out.
Have fun
dave g
 
Posts: 715
Joined: Fri, 18 Oct 2013 6:59 +0000

Re: Priming water filter separator?

Postby Morksvigo05 on Wed, 25 Jul 2018 7:05 +0000

Thanks mate
I'm guessing the hose that goes to the fuel rails ?
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Priming water filter separator?

Postby Morksvigo05 on Wed, 25 Jul 2018 7:06 +0000

Would it be better to fill the water separator filter to or?
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Priming water filter separator?

Postby Morksvigo05 on Thu, 26 Jul 2018 7:58 +0000

Hi guys just an update after 200 pumps at least on the primer I was getting no where not a drop I remembered I had a oil transfer pump like the little ones on the hand soaps but a bit bigger was for my outboard lower leg anyways it got the job done real quick very happy and thanks for the advice Dave
Champion mate
Cheers
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Priming water filter separator? ** Fixed**sorta

Postby Morksvigo05 on Thu, 26 Jul 2018 3:30 +0000

Ok guys I've come across a bit of a problem
Truck drives awesome once going and starts first kick say if I fill up fuel stop n start but when it's been sitting for like half hour it takes a lil bit to start like not by much but noticeable to me
And sometimes idles for ten seconds then stops
After a little bit more cranking turns on and stays on
I took it for a drive today like 100 K didn't miss a beat
Checked all my hoses all tight checked Allround no leaks etc?
Any body experience this
One thing I thought it could be is because I used the primer so much might have worn something in there?
And if it was air wouldn't a hundred K drive would of been passed through ?
Any info much appreciated as always guys
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Priming water filter separator? ** Fixed**sorta

Postby Gipsy on Thu, 26 Jul 2018 4:41 +0000

Did you say you have a prefilter? If it has a glass bowl? Is it full? Sounds like you have air in the system somewhere. Take the delivery hose off (the one between the OEM filter and the common rail) put it into a glass jar and pump the primer again to purge any air, probably in the prefilter. After purging reconnect the hose and pump the primer again til it goes hard.

Pity you used that oil pump, if you used it after the OEM filter you may introduce some contamination. Never do this, use the primer on the OEM filter.

Otherwise it may be the oring on the filter leaking ( sucking air)
Cheers Gipsy :D although I'm sure somebody will challenge that :lol: even Einstein wasn't certain of his theories.
My 2013 auto D4D DC SR5, prefilter, 3" exhaust and Chip with egt probe, stock SR5 rims with Toyo Open Country AT2 265/65R/17's
Gipsy
 
Posts: 2135
Joined: Tue, 07 May 2013 2:00 +0000
Location: South Coast NSW and all over Oz

Re: Priming water filter separator? ** Fixed**sorta

Postby Morksvigo05 on Thu, 26 Jul 2018 5:01 +0000

Oh no I done this already to prime worked awesome I flushed it plenty of times over with clean diesel just incase even tho I primed it into a jar nothing went in only out into the jar if this makes sense
I think I'm gradually losing rail pressure due to an O ring or something like that
Pain in the ass
But getting to know these diesels like the back of me ol fella lol
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Priming water filter separator? ** Fixed**sorta

Postby Morksvigo05 on Thu, 26 Jul 2018 5:35 +0000

This is what it seems to be doing
Cranks over and fires fine idles for like 20 30 seconds
Then stalls
Crank again takes about 4 seconds of cranking then starts and idles fine and doesn't stall again and runs fine?
I know it's something to do with one of the filters
Looks like I might have to do the whole thing again other thing I used a Cooper filter instead of a Toyota one for the factory filter housing and the water separator is a ryco maybe there's an O ring in there that's no good
Not a buggy but a real pain
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Priming water filter separator? ** Fixed**sorta

Postby dave g on Thu, 26 Jul 2018 6:44 +0000

Definitely sounds like you're sucking in air some way
dave g
 
Posts: 715
Joined: Fri, 18 Oct 2013 6:59 +0000

Re: Priming water filter separator? ** Fixed**sorta

Postby Morksvigo05 on Thu, 26 Jul 2018 8:12 +0000

For sure Dave gonna get straight on it tomorrow Arvo
I'll let Yas know how I go
Got to be from one of the two filters
Wasn't happening before I changed them
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw

Re: Priming water filter separator? ** Fixed**

Postby Morksvigo05 on Fri, 27 Jul 2018 3:30 +0000

Hi guys just wanted to let Yous know I fixed my issue took me a while as nothing looked a miss
But ended up changing the whole water separator housing as the new filter I got had orings and stuff with it but there was a couple that didn't come with it so yeah changed the whole thing very very happy
Thanks for your help guys
Morksvigo05
 
Posts: 34
Joined: Sat, 23 Jun 2018 2:58 +0000
Location: Cowra nsw


Return to Fuel Systems

Who is online

Users browsing this forum: No registered users and 7 guests



cron