How to clean your map sensor filter

Re: How to clean your map sensor filter

Postby alexisdmtr on Sun, 30 Nov 2014 1:36 +0000

AdamHC wrote:
alexisdmtr wrote:
Talktheroo wrote:[quote="alexisdmtr"]So I decided to call the toyota office today and ask them about maf sensor and see what they know about it.I was surprised to hear the chief engineer there (30yr old something guy) to know exactly was I was asking.He explained to me how it works (exactly what you all guys say here) and he said that they clean it when asked lol with a carb cleaner at every 50k his opinion was.

Do not clean the MAF sensor with carby cleaner. MAF Cleaner only. You will get a residue from the carby cleaners.
Carby cleaner for the MAP filter only. Make sure you use compressed air to get any residue out of the internals of the MAP filter, as well.
The Roo.

Damn ....where were you yesterday b4 having them cleaned with carb cleaner:)...I looked around though and couldnt find a maf cleaner.Not even toyota sells them...

I just picked mine up from Autobarn[/quote]
No autobarn here...ebay it is I guess...not sure though if they ship sprays
User avatar
alexisdmtr
 
Posts: 319
Joined: Wed, 16 Jul 2014 3:06 +0000


 

Re: How to clean your map sensor filter

Postby alexisdmtr on Mon, 01 Dec 2014 2:22 +0000

Carb cleaner and brake cleaner are the same? Anyhow..I dont know if it a concidense or what but after the maf&map cleaning (nothing major came out by the way) today on my way to work I averaged 9l/100km where I used to do it with 10+.Same driving and all...I guess it works?
User avatar
alexisdmtr
 
Posts: 319
Joined: Wed, 16 Jul 2014 3:06 +0000

Re: How to clean your map sensor filter

Postby Brewer on Tue, 06 Jan 2015 5:30 +0000

Talktheroo wrote:MAF sensor location.

You have to undo the two screws, and then take out the MAF sensor. If you are unplugging, make sure you take off the negative terminal on the main battery. Make sure you take off the O ring seal, as MAF cleaner will damage it. Look into the bottom of the sensor and locate the two hot wires.
Spray some MAF sensor cleaner into where the hot wires are. You do this until the hot wires are clean.



Hi Roo. Just out of interest, can leaving the battery active when unplugging cause an arc and damage the MAF sensor? Or is there another reason to isolate the battery?
Brewer
 
Posts: 120
Joined: Tue, 19 Nov 2013 6:08 +0000
Location: Victoria

Re: How to clean your map sensor filter

Postby millsi on Sat, 09 May 2015 8:23 +0000

Cleaned mine today at 310k km. Not sure if it had been done before, wasn't too bad but definitely had some crud come out.
millsi
 
Posts: 140
Joined: Wed, 25 May 2011 4:52 +0000

Re: How to clean your map sensor filter

Postby RogerRamjet on Sun, 17 May 2015 10:06 +0000

Tried to do this today.

Let me just say that I have never ever felt so emasculated and less of a man than today lol.

I could not remove the map sensor if my life depended on it.

I managed to remove the hose from the bottom, but could not for the life of me remove the sensor from the top hose. It was such a tight fit and would barely move.

I cant be the only one to experience this can I? Any tips for making it easier to do so. I honestly feel if I add any more force trying to remove it, the sensor will break
RogerRamjet
 
Posts: 10
Joined: Sat, 16 Nov 2013 6:15 +0000

Re: How to clean your map sensor filter

Postby fnqtech on Mon, 18 May 2015 7:56 +0000

Just for those having difficulty find MAP sensor cleaner, it is available from REPCO, Supercheap and Austobarn (to name a few) as CRC Mass Air Flow Sensor Cleaner
fnqtech
 
Posts: 127
Joined: Sat, 03 Mar 2012 3:12 +0000
Location: Townsville

Re: How to clean your map sensor filter

Postby lindsay84 on Tue, 19 May 2015 8:51 +0000

Hi Guys.
I have cleaned the EGR,MAF,MAP Intake manifold 2000k ago and injector seats replaced.Ive connected it to techstream and have started it cold and MAF readings are 8.14g.Once upto 85 degrees I have checked it and its reading 17.8 gm.All filters are new oil,air and fuel.It smells like its running rich when up to temp.You reckon the MAF sensor has shit its self.
lindsay84
 
Posts: 27
Joined: Thu, 21 Feb 2013 5:37 +0000

Re: How to clean your map sensor filter

Postby Locknut on Tue, 19 May 2015 4:48 +0000

Just did mine, a slight power change. Seems to be sounding 'healthier'. L/100km are yet to be determined.

For those interested, supercheap will find you the actual replacement MAP sensor filter for $95. They call it a boost sensor filter if anyone needs a replacement.

Another fine thread! Cheers :D
User avatar
Locknut
 
Posts: 117
Joined: Wed, 22 Oct 2014 4:00 +0000
Location: Frankston South, Vic

Re: How to clean your map sensor filter

Postby tiv on Tue, 21 Jul 2015 11:16 +0000

Tried this myself, with CRC contact cleaner, couldn't source the MAF product, did wonders in terms of power gain and fuel economy, thanks
tiv
 
Posts: 4
Joined: Wed, 10 Jul 2013 5:45 +0000

Re: How to clean your map sensor filter

Postby Talktheroo on Thu, 23 Jul 2015 3:36 +0000

It's a good idea to clean the MAP filter with carby cleaner.

Image

MAP filter.
The Roo.
Passing through country and seeing country are two different things.
User avatar
Talktheroo
 
Posts: 1204
Joined: Sun, 24 Feb 2013 12:45 +0000
Location: Brisbane.

Re: How to clean your map sensor filter

Postby Chris2007 on Mon, 27 Jul 2015 2:24 +0000

I noticed my filter was upside down compared to the one shown in the pictures. Do they work both ways?
Chris2007
 
Posts: 2
Joined: Mon, 10 Feb 2014 6:05 +0000

Re: How to clean your map sensor filter

Postby Talktheroo on Sun, 02 Aug 2015 3:42 +0000

Chris2007 wrote:I noticed my filter was upside down compared to the one shown in the pictures. Do they work both ways?

Grey barb down at the bottom, Chris.
Black barb at the top.
The Roo.
Passing through country and seeing country are two different things.
User avatar
Talktheroo
 
Posts: 1204
Joined: Sun, 24 Feb 2013 12:45 +0000
Location: Brisbane.

Re: How to clean your map sensor filter

Postby Rayne on Mon, 31 Aug 2015 9:58 +0000

Cleaned both the other week, both were dirty. I haven't experienced a power gain but fuel economy is a little better. Judging by my Map sensor filter I'm guessing my intake is pretty bad.
User avatar
Rayne
 
Posts: 68
Joined: Tue, 07 Aug 2012 4:36 +0000

Re: How to clean your map sensor filter

Postby ahmadmoghrabi on Sun, 27 Sep 2015 8:07 +0000

My Hilux D4D 2500 turbo 2 Cabin 2012 Diesel, engine light on after 30 minutes from starting, then losing engine power, switching off and on the light goes off and again the same problem occur. Any one can advise me about this problem.
ahmadmoghrabi
 
Posts: 2
Joined: Tue, 22 Sep 2015 2:46 +0000
Location: Saudi Arabia

Re: How to clean your map sensor filter

Postby Talktheroo on Sun, 04 Oct 2015 6:36 +0000

ahmadmoghrabi wrote:My Hilux D4D 2500 turbo 2 Cabin 2012 Diesel, engine light on after 30 minutes from starting, then losing engine power, switching off and on the light goes off and again the same problem occur. Any one can advise me about this problem.

A fault code has been stored in the ECM (engine light symbol).
You will have to take the vehicle to someone who can do a diagnostic on it.
The Roo.
Passing through country and seeing country are two different things.
User avatar
Talktheroo
 
Posts: 1204
Joined: Sun, 24 Feb 2013 12:45 +0000
Location: Brisbane.

Re: How to clean your map sensor filter

Postby Chippy on Mon, 23 Nov 2015 5:06 +0000

I gave the filter a clean out today. Quite a bit of black stuff came out. And then it finally ran clear. Noticed the boost come on almost instantly with a quick run round the block, very slight increase in power, though it may all be in my head after reading these forums a little too eagerly. Hoping for a result at the pump more than anything!
Lost is just a frame of mind
Chippy
 
Posts: 21
Joined: Sun, 11 Oct 2015 9:27 +0000
Location: Baldivis, W.A

Re: How to clean your map sensor filter

Postby gtsteve on Tue, 24 Nov 2015 11:15 +0000

Bugger. I just cleaned my MAP and that was very disappointing, I was wanting it dirty and a power increase but it was clean after 100,000 odd K's and no reason even to take the truck out to look for a difference in spoolup.

I could blow and suck through the filter easily before squirting carby cleaner into it which came out clear on white tissue paper. Mind you my provent oil catch-can works a treat, I have to drain it regularly, all of the oil apparently is stopped there, as mentioned earlier.

Mmmm, maybe I'll just adjust up the back brakes again, that is always guaranteed to make a noticeable improvement. :lol:
Steve & Liz

'09 SR5 Hilux diesel auto. Stanadyne primary fuel filter/water separator, Provent 200 oil/air separator, Rear camera, key/door buzzer killed, Long range fuel tank, Oil cooler and Snorkel.
User avatar
gtsteve
 
Posts: 130
Joined: Sat, 30 Nov 2013 4:39 +0000
Location: Cronulla NSW

Re: How to clean your map sensor filter

Postby Talktheroo on Wed, 25 Nov 2015 4:48 +0000

gtsteve wrote:Bugger. I just cleaned my MAP and that was very disappointing, I was wanting it dirty and a power increase but it was clean after 100,000 odd K's and no reason even to take the truck out to look for a difference in spoolup.

I could blow and suck through the filter easily before squirting carby cleaner into it which came out clear on white tissue paper. Mind you my provent oil catch-can works a treat, I have to drain it regularly, all of the oil apparently is stopped there, as mentioned earlier.

Mmmm, maybe I'll just adjust up the back brakes again, that is always guaranteed to make a noticeable improvement. :lol:

:lol: ;)
The Roo.
Passing through country and seeing country are two different things.
User avatar
Talktheroo
 
Posts: 1204
Joined: Sun, 24 Feb 2013 12:45 +0000
Location: Brisbane.

Re: How to clean your map sensor filter

Postby Talktheroo on Sun, 29 Nov 2015 10:52 +0000

Image

Image

Just something small.
See the gap with the hose down the bottom where the arrow is, that's because there is a plastic barb on the map filter.
You are not supposed to push the hose all the way like what has happened in the above hose. There should be a gap like the bottom hose.
When you have a look at the design of the map filter when you go to clean it, you will know what I mean.
By pushing the hose all the way damages the end of the hose.
If this has happened you can just cut off the damaged bit at the end and start again.
The Roo.
Passing through country and seeing country are two different things.
User avatar
Talktheroo
 
Posts: 1204
Joined: Sun, 24 Feb 2013 12:45 +0000
Location: Brisbane.

Re: How to clean your map sensor filter

Postby Jesse98 on Wed, 20 Jan 2016 1:30 +0000

Bit of an older thread but I just cleaned her out and black stuff came pissing out. Very well done fellas :D
CHECK OUT MY BUILD viewtopic.php?f=50&t=26344
User avatar
Jesse98
 
Posts: 93
Joined: Mon, 14 Sep 2015 3:09 +0000
Location: Dubbo, nsw

PreviousNext

Return to Tips & Tricks

Who is online

Users browsing this forum: No registered users and 7 guests