NewHilux.net

Does anyone have a list of x guages that work with a 2022 hilux for a scanguage?
On my 2017 model I had a lot more than is listed on the scanguage website for the 2022 model.
Silverfox

Anyone?

some ideas here.. also suggests looking at pradopoint

viewtopic.php?f=122&t=29367&start=20

These Scangauge II x-gauge codes work on my 2021 Prado so most could be worth a try on the latest Hilux

ITEM TXD RXF RXD MTH NAME STATUS REMARKS
Exhaust Gas Temp 07DF0178 054106780000 3810 0001000AFFD8 EGT Works EGT Bank 1 Sensor 1 (°C)
DPF Temp 07DF0178 032100000000 2010 0001000AFFD8 DPF Works EGT Bank 1 Sensor 3 (°C)
Transmission Pan Temp 0700221AAA C462051A36AA 3008 00010001FFD8 ATF Works Trans Temp Sensor 1 (°C)
Transmission Torque Converter Temp 0700221AC0 C462051A36C0 3008 00010001FFD8 TCT Works Trans Temp Sensor 2 (°C)
Transmission Current Gear 0700221AA0 C462051A36A0 3008 000100010000 GER Works Trans Gear Selected (1 for P/N/R/1)
Fuel Level 07C02129 046185290000 2808 000500010000 FLV Works XX.X Litres
Barometric Pressure 07DF0133 044185330000 2808 006400450000 BP Works PSI
Ambient Temperature 07DF0146 044105460000 2808 00010001FFD8 AIR Works Outside Ambient Air Temp (°C)
Intake Manifold Absolute Pressure 07DF0187 044185870000 3010 000C01090000 MAP Works PSI
Turbo Boost Pressure 07DF0187 044185870000 3010 000C0109FF6D BST Works PSI (MAP value -14.7 PSI Sea level Barometric Pressure)
Commanded Turbo Boost Pressure 07DF0170 054186700000 3810 000C0109FF6D BSC Works PSI (value -14.7 PSI Sea level Barometric Pressure)

DPF In/Out Delta Pressure 07DF017A 0541067A0000 3810 000100640000 DPD kPa (XXX)
DPF In/Out Delta Pressure 07DF017A 0541867A0000 3810 000100450000 DPD PSI (XX.X)

Thanks ptommo59.
A lot of those x-guage codes work.
With the turbo boost pressure gauges you have "value - 14.7 psi sea level". Is this an adjustment I need to make with the scanguage?
On mine I'm seeing peaks around 29 ( not sure if it's lbs) which is around 10 lb (?) More than I got on my '17 model. Seams pretty high. Are your readings on boost similar?
Silverfox

Hi Silverfox1111,

If you key in the Barometric Pressure codes you can get your local reading which in my case is 14.3 PSI and adjust the last 4 digits FF6D in the Boost reading to match using the table below. Its only 0.4 PSI so not really significant.

MAP/BST PSI Offset MTH last 4
14.2 FF72
14.3 FF71
14.4 FF70
14.5 FF6F
14.6 FF6E
14.7 FF6D
14.8 FF6C


The reading is in PSI and you will see significantly higher readings with the 150 kw engine over the older 130 kw due to the lager turbo.

Hi Silverfox1111,

If you key in the Barometric Pressure codes you can get your local reading which in my case is 14.3 PSI and adjust the last 4 digits FF6D in the Boost reading to match using the table below. In my case Its only 0.4 PSI difference so not really significant.

MAP/BST PSI Offset MTH last 4
14.2 FF72
14.3 FF71
14.4 FF70
14.5 FF6F
14.6 FF6E
14.7 FF6D
14.8 FF6C

The Boost reading is in PSI and you will see significantly higher readings with the 150 kw engine over the older 130 kw due to the larger turbo (which is how its making the extra power and torque).

I haven't really checked mine so will have a look to see if it peaks around similar value to yours.

Ptommo59

Hi Silverfox1111,

I checked and yes my peak Boost is coming up around same value as yours .

I have also found Torque Converter lock Codes which work if you are interested

TXD 0700221A80
RXF C462051A3680
RXD 3008
MTH 000100010000
Short Name: TCL
Torque Converter Lock status 0 = Unlocked / 1 = Locked

or alternative

TXD 0700221A80
RXF C462251A3680
RXD 3008
MTH 000100010000
Short Name: TCL
Torque Converter Lock status OFF = Unlocked / ON = Locked

I have put lots of updates on the Prado Jul 2021+ model scangauge codes here on Pradopoint https://www.pradopoint.com.au/forum/-15 ... -21-models.
Most should also work on the 150kw version Hilux and any starting with 07DF01 should work on most post 2006 vehicles with OBDII connectors.
Hope this is helpful to someone out there.

Ptommo59
Your a legend. The codes you gave me earlier all work.
Your a better resource than scanguage themselves.
Silverfox

No Probs Silverfox1111,

While I'm playing around in this space any other parameters not on my list that you think are worth chasing down?

Hi All,

I just added a range of the fuel injection system parameter codes for the 150KW 1GD-FTV on Pradopoint in this link https://www.pradopoint.com.au/forum/-15 ... -21-models if anyone is interested.

These should work but will need the formulas in the MTH column verified. So if anyone uses them and has access to Techstream or a Scantool can you cross check that the gauge is reading correct or close enough and provide feedback (as there is a limitation on the maths that you can do with the Scangauge MTH so some can be out by a small margin).