Chaps 2008 D4D SR5 build

Want to show off what you've done to your rig? or have a custom project to show? Post it up here!

Re: Chaps 2008 D4D SR5 build

Postby FAIL on Mon, 02 Jun 2014 6:30 +0000

Nice work on the Hilux. It's going down a very similar path to mine. Plus I've got an Evo X too :-)
User avatar
FAIL
 
Posts: 111
Joined: Fri, 23 Nov 2012 6:33 +0000
Location: Sunshine Coast


 

Re: Chaps 2008 D4D SR5 build

Postby ONBAGZ on Fri, 01 Aug 2014 4:22 +0000

This is awsome good job
User avatar
ONBAGZ
 
Posts: 272
Joined: Sat, 12 Jul 2014 9:25 +0000
Location: Wangaratta

Re: Chaps 2008 D4D SR5 build

Postby swhilux on Fri, 01 Aug 2014 5:50 +0000

Love the fit out and electrics. Great work
swhilux
 
Posts: 159
Joined: Sat, 02 Nov 2013 4:05 +0000
Location: South West WA

Re: Chaps 2008 D4D SR5 build

Postby kitdoctor on Sat, 02 Aug 2014 11:47 +0000

x2 to all the compliments, well done on your mods. MONGO
User avatar
kitdoctor
 
Posts: 535
Joined: Wed, 22 Jan 2014 7:30 +0000

Re: Chaps 2008 D4D SR5 build

Postby hunty on Wed, 20 Aug 2014 8:20 +0000

brilliant mate. absolutely brilliant!

my car feels inept compared to yours, thanks for that
hunty
 
Posts: 1
Joined: Sat, 11 Aug 2012 12:33 +0000

Re: Chaps 2008 D4D SR5 build

Postby chappelle on Fri, 31 Oct 2014 7:55 +0000

I havn't updated this for a while, but finally have something for you all to see.

Just installed a roof top tent, now I can't wait to go camping :D

Image

Image

Image

This is the inside, nice foam mattress

Image

Image

All supported by an internal frame that bolts onto the tray, forgot to take a picture of this, ill do that next time.

You will also notice i have put an LED strip under the awning, provides nice light when sitting under the canopy at night with very little current draw, i think i'll put some of these inside of the tent too.

Image

Image

And also i installed a tablet holder, this will run my HEMA maps and any other navigation stuff on my Samsung Galaxy Tab S 10.5

Image
chappelle
 
Posts: 19
Joined: Sat, 12 Oct 2013 4:38 +0000
Location: Perth, Western Australia

Re: Chaps 2008 D4D SR5 build

Postby chappelle on Fri, 28 Nov 2014 12:30 +0000

Here it was when out camping and all in use.

Image

Next on my list to do is get some new tires, i have been looking around and think i might go for tyres in 265/75/16 with some 16x7 +20 sunrasias

I want mud terrain tyres but also dont want too much road noise as i probably spend most of the time on the road, does anyone have any suggestions for a reasonably quiet MT tire?
chappelle
 
Posts: 19
Joined: Sat, 12 Oct 2013 4:38 +0000
Location: Perth, Western Australia

Re: Chaps 2008 D4D SR5 build

Postby jaybags on Fri, 28 Nov 2014 5:57 +0000

Set up looks good.

Not too experienced with muddies, but an alternative may be Cooper ST Maxx or MT P3's, they're a "hybrid" all terrain, 50% mudd / 50% road. Pretty quiet on road and handle offroad well.
Cheers,
Jay


My (super slow) build - viewtopic.php?f=50&t=20120
User avatar
jaybags
 
Posts: 1213
Joined: Thu, 23 May 2013 11:17 +0000
Location: Melbourne

Re: Chaps 2008 D4D SR5 build

Postby wmackay on Fri, 28 Nov 2014 5:06 +0000

Super clean rig mate!
Love the evo too. My favourite model. They just scream tough! I'd love one, one day
wmackay
 
Posts: 54
Joined: Fri, 10 Oct 2014 4:07 +0000
Location: Woonona

Re: Chaps 2008 D4D SR5 build

Postby chappelle on Tue, 24 Feb 2015 12:07 +0000

Have not updated this for a while and I still didn't take all the pictures I wanted to take, i'll get around to it.

For now, ill post what i have.

I put on a new tyre and rim combo.
Achillies Desert Hawk XMT tyres, 265/75/r16 with 16x7 sunraysia style rims +20 or +30 I cant remember...
Very pleased with them so far, allthough they are ofcourse quite noisy on the road anything over around 85kph

Image

A while ago i did the rear seat mod, back here for now i just keep my sand tracks because they went all discoloured on the roof rack in the sun. opens up the space to use for other stuff if needed.

Image

Image

Few other things i have done but not noted or have good pictures for:

Jerry can holder on the roof rack
9KG gas tank holder on the roof rack (BBQ gas)
put on new oricom ANU1000 town and country UHF antenna pack
Permanently installed LED light strip in roof top tent

Have also just ordered some more rear lighting for night time 4wding.

Looking at getting a solar pannel for those longer camp stays, and also hopefully getting some rock sliders made up soon.
Last edited by chappelle on Wed, 18 Mar 2015 10:11 +0000, edited 1 time in total.
chappelle
 
Posts: 19
Joined: Sat, 12 Oct 2013 4:38 +0000
Location: Perth, Western Australia

Re: Chaps 2008 D4D SR5 build

Postby chappelle on Wed, 18 Mar 2015 10:03 +0000

Another quick update, haven't taken any proper photos yet.

Installed some more rear lighting
Image

Made a set of sliders with my welder friend, heres some photos of the progress of them being made and test fitted, they are currently getting powdercoated so not installed yet.

Image

Image

Image


Installed a 100w solar panel on the roof to run all my accessories on longer stay trips.
Connects up to my cTek d250s battery charger
Image

Also put in a voltmeter to easily keep an eye on my battery
Image

Up next to install the sliders, and perhaps an on board 12v water system.
Stay tuned.
chappelle
 
Posts: 19
Joined: Sat, 12 Oct 2013 4:38 +0000
Location: Perth, Western Australia

Re: Chaps 2008 D4D SR5 build

Postby chappelle on Sat, 30 May 2015 5:49 +0000

Heres some new pics of a few thigns, and a few new things i have added.

The sliders were poweder coated and installed.
Image

Also added rated recovery points onto the front.
Image

and the other side
Image

and from the rear
Image

and a close up
Image

Next, i did end up installing a water tank, its 39L and sits in the right hand side of the drawer system.

Image

Its all safe for drinking water, uses a 12v water pump
Image

get decent flow out of it, enough for rinsing things down - could use it to shower or wash dishes and fill water bottles.
Image

Here is also a better picture of the new rear lighting
Image

And also a better picture of the solar panel on the roof rack
Image

Also got a new camp cooker, i just leave this up here ontop of the fridge
Image

Also a better shot of the roof top tent support bars, probably seen them before but puts the weight on the tub rather than the fiberglass canopy.
Image

And another view from ontop
Image

I got a rechargable LED lenser torch, i like these because they have a nice magnetic USB charger, mounted it onto the drawer system and hard wired it in so i can always have a fully charged torch on hand.
Just put a USB socket inside that left hand wheel arch area for it to plug into neatly out of sight.
Image

And finally, i also installed a high lift jack and shovel mount on the roof rack
Image
chappelle
 
Posts: 19
Joined: Sat, 12 Oct 2013 4:38 +0000
Location: Perth, Western Australia

Re: Chaps 2008 D4D SR5 build

Postby fracturedranga on Sat, 30 May 2015 8:45 +0000

nice setup and build, where did you get your 12v water gear from? and whats the dimensions of your solar panel, im looking for one to fit on my tray roof atm
User avatar
fracturedranga
 
Posts: 920
Joined: Fri, 12 Dec 2014 12:22 +0000
Location: dalby

Re: Chaps 2008 D4D SR5 build

Postby chappelle on Sun, 31 May 2015 1:30 +0000

Thanks!

The water stuff mostly ebay:

12v pump - http://www.ebay.com.au/itm/370713211023?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

Tank - http://www.ebay.com.au/itm/39-LITRE-LOW-PROFILE-MARINE-BOAT-RV-CARAVAN-CAMPER-VAN-FRESH-DRINKING-WATER-TANK-/201189111557

And a few other fittings and things was from bunnings, drinking water hose i got from a 4x4 show.

solar panel dimensions are: 1015 L x 670 W x 30 D mm
chappelle
 
Posts: 19
Joined: Sat, 12 Oct 2013 4:38 +0000
Location: Perth, Western Australia

Re: Chaps 2008 D4D SR5 build

Postby rds_929 on Mon, 28 Dec 2015 1:32 +0000

what jack and shovle mount did you go for ??? kaymar ?? i know there are a few different models and some don't work with the high lift jack and can't open the door
rds_929
 
Posts: 402
Joined: Mon, 01 Jun 2015 6:26 +0000
Location: melbourne , victoria

Re: Chaps 2008 D4D SR5 build

Postby chappelle on Sat, 12 Mar 2016 2:43 +0000

I havn't posted for a while so I have a bit of an update since last time.
Well I did some night time 4wding out on the power lines track and did a little panel damage on the rear tub a while ago, it it was nothing major but bugged me for ages, i had a look on the web and found one come up on gumtree in the right colour and near to my place, bought this one in good nick for $400 and sold my damaged one for $200 so for only $200 fixed my damaged tub

It was a pretty major job to change it over though, first of all have to remove the roof top tent
Image

Lucky had a stacker at work to help with removing this.
You can see the damage on this side around the tail light, there is also damage on the left side of the tub, hence why i wanted to replace it.
Image

Removed all the drawers, all the wiring, water tank, aux battery, support bars for roof tent, everything out basically and then the tub off
Image

New tub on
Image

Then the canopy back on
Image

Did the wiring as neat as i could as I went, wiring up to the solar panel and the led strip in the awning
Image

Re-installed all the wiring back in the left side in the void left of the drawer system
Image

Image

Image

Image

This time I also put in some seals on the tailgate to try stop some dust coming in
Image

Got the drawer back in
Image

wiring all tucked in the left cubby
Image

back on the road and moving, it came with a de-badged tailgate which i quite liked but the missus said it looks gay without Toyota written on it so i swapped the tailgates after this

Image

It was all a bit of a mad rush to get it back together, I finished the job pretty much the day before going on a 5 day trip down south
Image
Image
All went well and nothing failed
chappelle
 
Posts: 19
Joined: Sat, 12 Oct 2013 4:38 +0000
Location: Perth, Western Australia

Re: Chaps 2008 D4D SR5 build

Postby chappelle on Sat, 12 Mar 2016 2:49 +0000

rds_929 wrote:what jack and shovle mount did you go for ??? kaymar ?? i know there are a few different models and some don't work with the high lift jack and can't open the door


Sorry for the late reply, it was not a branded one - I got it from an ebay store called 'southportautorecyclers' but they don't have the item listed any more.
It had this description if you want to find something similar: 48" HI HIGH LIFT JACK FARM WITH ROOF RACK MOUNTING BRACKETS 4WD 4x4 3000kg *NEW*
chappelle
 
Posts: 19
Joined: Sat, 12 Oct 2013 4:38 +0000
Location: Perth, Western Australia

Re: Chaps 2008 D4D SR5 build

Postby rds_929 on Sat, 12 Mar 2016 7:12 +0000

chappelle wrote:
rds_929 wrote:what jack and shovle mount did you go for ??? kaymar ?? i know there are a few different models and some don't work with the high lift jack and can't open the door


Sorry for the late reply, it was not a branded one - I got it from an ebay store called 'southportautorecyclers' but they don't have the item listed any more.
It had this description if you want to find something similar: 48" HI HIGH LIFT JACK FARM WITH ROOF RACK MOUNTING BRACKETS 4WD 4x4 3000kg *NEW*



legend thanks bud appreciate also are your recovery points road safe ?? iv'e got the same but just about to put my arb bull bar on and hoping they will still fit
rds_929
 
Posts: 402
Joined: Mon, 01 Jun 2015 6:26 +0000
Location: melbourne , victoria

Re: Chaps 2008 D4D SR5 build

Postby chappelle on Sat, 12 Mar 2016 8:38 +0000

rds_929 wrote:
chappelle wrote:
rds_929 wrote:what jack and shovle mount did you go for ??? kaymar ?? i know there are a few different models and some don't work with the high lift jack and can't open the door


Sorry for the late reply, it was not a branded one - I got it from an ebay store called 'southportautorecyclers' but they don't have the item listed any more.
It had this description if you want to find something similar: 48" HI HIGH LIFT JACK FARM WITH ROOF RACK MOUNTING BRACKETS 4WD 4x4 3000kg *NEW*



legend thanks bud appreciate also are your recovery points road safe ?? iv'e got the same but just about to put my arb bull bar on and hoping they will still fit


The recovery points I bought from opposite lock, cant remember the brand. They fit fine for me, maybe a little bending and squeezing the side bash plate type things at either side under the bull bar but not hard from what I remember
chappelle
 
Posts: 19
Joined: Sat, 12 Oct 2013 4:38 +0000
Location: Perth, Western Australia

Re: Chaps 2008 D4D SR5 build

Postby rds_929 on Sat, 12 Mar 2016 8:52 +0000

awsome thanks mate yeah that's where i got mine from pretty sure they're the same any chance you could get a few close up pics of how the recovery points are mounted ??
rds_929
 
Posts: 402
Joined: Mon, 01 Jun 2015 6:26 +0000
Location: melbourne , victoria

PreviousNext

Return to Member Build Ups

Who is online

Users browsing this forum: No registered users and 7 guests